Featured image for: Bicycle Torque Specs: Complete Guide by Component
Torque Guides November 8, 2026 8 min read

Bicycle Torque Specs: Complete Guide by Component

Bicycle torque specs by component: stem, seatpost, pedals, cranks, brakes and derailleurs, in Nm and ft-lbs.

Shaheer Akram Torque conversion specialist

Bicycle bolts are small, light, and easy to damage, which is exactly why torque specifications matter more on a bike than on a car. A car wheel nut tightened a little too much usually survives. A carbon handlebar clamp or a seatpost bolt tightened a little too much can crack, and a cracked carbon part fails without warning. This guide covers the torque specifications for every component you will touch on a modern bicycle, in Newton-meters and foot-pounds, and explains how to apply them without damaging anything.

Why bicycle torque is different

Three things make bicycle torque special. First, the values are small: most bicycle fasteners tighten to between 4 and 15 Nm, which is a fraction of car values, so a small absolute error is a large percentage error. Second, many parts are carbon fibre or thin-walled aluminium, which crack or crush instead of bending when over-tightened. Third, bicycle torque wrenches are smaller tools: a typical bike torque wrench is a quarter-inch drive tool covering roughly 2 to 20 Nm, and using a big automotive wrench on a 5 Nm bolt gives you almost no feel for the correct setting. If you work on bikes, get a small torque wrench, or at least a set of preset torque keys for the common values.

How to read the specifications

Many bicycle components have their torque specification printed right on the part, usually near the bolt: look for text like ‘5 Nm’ or ‘Max 6 Nm’ on stems, seatpost clamps, and brake calipers. When the specification is printed on the part, that number wins over any general chart, including this one. When nothing is printed, use the component manufacturer’s manual for your exact model. The table below gives typical ranges from manufacturer guides, which cover the large majority of cases, but your specific component can differ, especially with carbon parts, which sometimes specify lower values than aluminium ones.

Bicycle torque specs by component

All values below are typical ranges published in manufacturer and brand support guides. Convert any Nm value with the homepage converter if your wrench reads ft-lb.

ComponentTypical torque
Stem bolts6-8 Nm (4.43-5.90 ft-lb)
Handlebar clamp bolts5-7 Nm (3.69-5.16 ft-lb)
Brake lever clamp bolts5-8 Nm (3.69-5.90 ft-lb)
Shift lever clamp bolts4-6 Nm (2.95-4.43 ft-lb)
Brake caliper mounting bolts6-10 Nm (4.43-7.38 ft-lb)
Seatpost clamp bolt5-6 Nm (3.69-4.43 ft-lb)
Saddle clamp bolts5-7 Nm (3.69-5.16 ft-lb)
Pedals35-55 Nm (25.81-40.57 ft-lb) per Shimano dealer manuals; many general guides list 30-35 Nm for other pedal systems
Rear thru axle12-15 Nm (8.85-11.06 ft-lb)
Rear derailleur mounting bolt8-12 Nm (5.90-8.85 ft-lb)
Chainring bolts (steel)10 Nm (7.38 ft-lb)
Chainring bolts (aluminium)8 Nm (5.90 ft-lb)
Crank pinch bolts (Hollowtech II type)10 Nm (7.38 ft-lb)
Square taper crank bolt40 Nm (29.50 ft-lb)
Disc brake rotor bolts4-6 Nm (2.95-4.43 ft-lb)

Pedals deserve special attention

Pedals are the most commonly mis-tightened bicycle part, for two reasons. First, the torque is much higher than people expect: Shimano’s dealer manuals specify 35 to 55 Nm for pedals, which is several times the value of a stem bolt. Second, the left pedal has a left-hand thread, which means it tightens counter-clockwise. If you force a left pedal clockwise, you will damage the crank arm. Grease the pedal threads lightly before fitting (unless your pedal maker says otherwise), start both pedals by hand to avoid cross-threading, then torque to the specification. A pedal that creaks under load is often a pedal that was never torqued properly in the first place.

Carbon parts: extra care

Carbon handlebars, seatposts, and frames are strong in the directions they are designed for and fragile in others. A carbon seatpost crushed by an over-tightened clamp is ruined, and the damage is often invisible from outside. Three rules protect carbon parts: always use a torque wrench, never exceed the value printed on the part, and use carbon assembly paste on carbon seatposts and handlebars. Carbon paste increases grip without extra clamping force, which lets you reach the specified torque without slipping. If a carbon part slips at the specified torque, do not just tighten harder: clean the surfaces, apply carbon paste, and re-torque to the specification.

Step by step: torquing a stem

  • Set your torque wrench to the specified value for your stem, usually 5 to 6 Nm for a four-bolt faceplate.
  • Tighten the faceplate bolts in a criss-cross pattern, a little at a time on each bolt, so the faceplate closes evenly.
  • Check the gap on both sides of the faceplate: it should be roughly equal top and bottom. An uneven gap means the bolts were not tightened evenly.
  • Torque the steerer clamp bolts (the ones that grip the fork steerer) to their specification, usually 5 to 6 Nm, alternating between them.
  • Check that the handlebar does not rotate in the clamp and the stem does not rotate on the steerer, then re-check after your first ride.

Common mistakes

  • Using a large automotive torque wrench on 5 Nm bolts. The wrench cannot resolve small values accurately, and you will overshoot without feeling it.
  • Tightening carbon parts by feel. Carbon gives almost no warning before it cracks. Always use the wrench.
  • Forgetting the left pedal’s reverse thread and forcing it the wrong way.
  • Tightening bolts one at a time to full torque instead of working up gradually in a pattern. This leaves clamps uneven and parts misaligned.
  • Ignoring the value printed on the component and using a generic chart instead. The printed value is specific to your part and always wins.

A full bike service, in torque order

When you service a whole bicycle, work in an order that avoids redoing steps. Start with the wheels: check the thru axles (12 to 15 Nm) and make sure both wheels are seated properly in the dropouts before anything else, because a wheel that is not seated changes every alignment you check afterwards. Next, do the cockpit: stem bolts, handlebar clamp, and brake and shift lever clamps, all in the 4 to 8 Nm range, tightened gradually and evenly. Then the brakes: caliper mounting bolts at 6 to 10 Nm, and check that the rotor runs true between the pads. Then the drivetrain: rear derailleur bolt at 8 to 12 Nm, chainring bolts at 8 or 10 Nm depending on material, and crank bolts to their specification. Finish with the seatpost and saddle: seatpost clamp at 5 to 6 Nm and saddle clamp at 5 to 7 Nm, with carbon paste on carbon parts. Working in this order means each adjustment is made on a bike that is already straight and true from the previous step.

One more habit belongs in every service: re-check the bolts you touched after the first ride. Newly fitted parts settle, especially stems and seatposts, and a bolt that was perfect on the stand can lose a little clamping force in the first hours of riding. This is the bicycle version of the car’s re-torque rule, and it takes two minutes with the torque wrench before your second ride.

Preset torque keys versus an adjustable wrench

A preset torque key is a small tool fixed to one value, usually 4, 5, or 6 Nm. It clicks or slips when it reaches its value, and it cannot be set wrong. An adjustable torque wrench covers a range and must be set for each bolt. Preset keys are cheaper, lighter, and ideal for travel or for a home mechanic who only touches stems and seatposts. An adjustable wrench is more versatile and necessary once you touch pedals, cranks, and thru axles, because those values span 5 to 55 Nm and no single preset key covers them. Many home mechanics end up with both: preset keys for the cockpit and a small adjustable wrench for everything else.

Frequently asked questions

Do I really need a torque wrench for a bicycle?

Yes, if you touch anything made of carbon or anything with a small bolt. A basic preset torque key set costs little and covers the common values. For everything else, a small adjustable torque wrench is one of the best tools a home mechanic can own.

What happens if I over-tighten a seatpost clamp?

On an aluminium frame, you can crush or ovalize the seat tube. On a carbon frame or post, you can crack it. Either way, the damage is expensive and sometimes invisible until the part fails.

Why do pedal specifications vary so much?

Different pedal systems use different thread sizes, materials, and crank interfaces. Shimano’s manuals specify 35 to 55 Nm, while some general guides list 30 to 35 Nm for other systems. Follow your pedal maker’s specification, not a generic number.

How do I convert Nm to ft-lb for my wrench?

Multiply Nm by 0.7375621493. For example, 10 Nm is 7.38 ft-lb, and 30 Nm is 22.13 ft-lb. The homepage converter does this instantly for any value.

How often should I check my bike’s bolts?

Check the bolts you touched after the first ride following any work, and give the whole bike a bolt check every few months of regular riding. Pay special attention to the stem, seatpost, and thru axles, because those are the bolts whose failure has the worst consequences.

Final word

Bicycle torque is about restraint, not strength. Most of the numbers in this guide are single digits, and the difference between right and cracked is a quarter turn. Use a small torque wrench, follow the value printed on the part, use carbon paste where it belongs, and re-check after the first ride. For the technique itself, read How to Use a Torque Wrench Correctly.

Written by

Shaheer Akram

Torque conversion specialist at Nm to Foot Pounds Converter, building accurate, accessible tools for mechanics, engineers, and DIYers.